About This Product
2015 -2023 Charger 392 Hellcat Blower Conversion .HPT Tune File
A professionally developed HP Tuners calibration file for 2015–2023 Charger 392, configured around the forced-induction combination named in this product. This is a downloadable calibration file intended to be used as a reference or starting point through HP Tuners Compare & Copy.
This is not a custom remote tune and it should not be blindly written to a different vehicle.
What You Are Purchasing
You are purchasing one downloadable HP Tuners .HPT calibration file for the combination shown in this product title. It is supplied as a professionally developed reference file—not as a VIN-specific custom calibration service.
Use the file to compare the source calibration against your own original read, then copy only the appropriate changes into your vehicle's file.
Built From Real-World Calibration Work
This file was developed from real-world J.R. Jones Racing calibration work for a supported combination. It gives knowledgeable HP Tuners users a stronger starting point than beginning with a completely stock file.
- Airflow, fuel, spark and torque-related calibration changes contained in the purchased file
- Forced-induction setup changes applicable to the listed combination
- A real-world calibration developed from supported J.R. Jones Racing work
- A downloadable .HPT file for reference and Compare & Copy use
Designed For
- 2015–2023 Charger 392 combinations matching the product title
- Vehicles with the same supported controller family and closely matching operating system
- Customers using HP Tuners Compare & Copy rather than blindly flashing an unrelated file
- Experienced tuners looking for a proven calibration reference or starting point
Product Details
- Application: 2015–2023 Charger 392
- Calibration: Hellcat Blower Conversion
- File format: HP Tuners .HPT
- Delivery: Digital download after purchase
- Recommended method: Compare & Copy into your original read
How To Use This File
Read and save your vehicle's original file using supported HP Tuners hardware and VCM Scanner/Editor software.
Open your original file and this purchased file in HP Tuners VCM Editor.
Use Compare to review the differences table by table. Confirm that each change applies to your controller, operating system and build.
Copy only the appropriate calibration changes into your own original file. Do not copy VIN, serial, security, segment or unrelated vehicle data.
Save as a new file, flash safely and datalog. Verify fuel trims, commanded fueling, spark, airflow, idle, transmission behavior and diagnostic operation before higher-load testing.
Before You Purchase
- Confirm the year range, engine, controller and calibration type match your application
- Confirm your operating system and available tables are compatible
- Know all engine, fuel system, transmission and drivetrain modifications
- Have the correct injector and sensor data when those parts differ from the source file
- Understand how to compare, copy, flash and datalog with HP Tuners
Not Included
- Custom remote tuning or VIN-specific revisions
- HP Tuners interface, credits or vehicle licensing
- Installation, mechanical repair or diagnostic labor
- Guaranteed compatibility with every operating system or hardware combination
- Automatic correction for different injectors, sensors, fuel, gearing or modifications
Compatibility Warning
Injector data, MAP sensor data, pulley size, fuel system, airflow hardware and operating system must match or be corrected for the vehicle. Never perform boost testing until fueling, sensor scaling and mechanical condition are verified.
Compare every section before copying. A calibration from another vehicle may contain different segment data, airflow models, injector information, transmission settings, diagnostic settings or hardware assumptions.
Do Not Blind-Flash This File
Writing an unmatched file directly to a controller can cause a no-start condition, poor drivability, incorrect fueling, transmission problems, diagnostic issues or controller recovery problems. Always build the final calibration from your vehicle's own original read unless the file has been specifically verified as a direct match.
Digital Product Notice
This is a downloadable digital calibration file. Because compatibility depends on the customer's vehicle, controller, operating system, hardware and modifications, the buyer is responsible for confirming suitability before use. Performance calibration should only be completed by someone who understands HP Tuners and can safely verify the result through proper datalogging.
Need a Tune Built Specifically for Your Vehicle?
This downloadable .HPT tune file is a proven starting point for HP Tuners users using Compare & Copy. If your vehicle has custom modifications, forced induction, injector changes, or you want a calibration built specifically for your exact combination, J.R. Jones Racing offers fully custom remote tuning with datalog revisions.
📦 Included With Every Download
Your purchase includes more than just the compare file.
🎥 Step-by-Step Video Tutorial
A detailed How to Compare Tune Files video is included with every downloadable tune. The video walks you through the entire process inside HP Tuners VCM Editor, including:
- Opening your factory tune
- Opening the downloaded compare file
- Using the Compare feature
- Opening the Compare Log (Ctrl + 5)
- Copying tables correctly
- Common mistakes to avoid
- Saving your completed tune correctly
Perfect for first-time users and anyone unfamiliar with the Compare feature.
📄 PDF Instruction Guide
You'll also receive a printable instruction guide:
📄 J.R. Jones Racing LLC - READ FIRST - How to Use Your Downloadable Tune File.pdf
This guide includes:
- Step-by-step written instructions
- Recommended tables to copy
- Important warnings about injector data
- Torque Management recommendations
- Calibration tab precautions
- Saving your completed tune correctly
- Final flashing and testing checklist
Both the video tutorial and PDF guide are included at no additional cost to help ensure you use your downloadable tune safely and correctly.
